Installation Engineering
PIPELAY ANALYSIS
PIPELAY ANALYSIS
- Start-up / Initiation
- Normal lay – Static & Dynamic
- Abandonment & Recovery
- Laydown
- Wet Buckle Recovery
- Above Water Tie-in
- Spool lift / Installation
- Beachpull / Horizontal Directional Drilling
- PLET Installation
- Riser stalk-on
![](https://marin-tek.com/wp-content/uploads/2023/08/pipelay-7.jpg)
![](https://marin-tek.com/wp-content/uploads/2023/08/pipelay-2.jpg)
![](https://marin-tek.com/wp-content/uploads/2023/08/pipelay-3.jpg)
![](https://marin-tek.com/wp-content/uploads/2023/08/pipelay-6.jpg)
![](https://marin-tek.com/wp-content/uploads/2023/08/pipelay-5.jpg)
STRUCTURAL ANALYSIS
![](https://marin-tek.com/wp-content/uploads/2023/08/Structure-1.jpg)
![](https://marin-tek.com/wp-content/uploads/2023/08/Structure-2.jpg)
Lift Analysis & Rigging design
- General Considerations
- Structure Weight and CoG from W.C.R.
- Minimum 60 deg sling angle.
- CoG shift consideration – 1m radius / as per guidelines
- Lifting Point Verification Checks (Padeyes / Trunnions)
- Hook Prong stability checks
- Rigging Selection from catalogues / existing inventory
Installation Aids Design
- Dynamic Load Factor = 2.0 or as per specifications
- 10 % out of plane loads
- Hydrostatic Pressure Checks
- Hydro test Pressure Checks
![](https://marin-tek.com/wp-content/uploads/2023/07/Installation-Aids-design-1.jpg)
![](https://marin-tek.com/wp-content/uploads/2023/07/Seafastening-design-and-Vessel-Motion-Analysis-1.jpg)
Seafastening design and Vessel Motion Analysis
- Self Weight of Cargo
- Vessel Motion (Motion Criteria / MOSES motions)
- Wind Forces
- Wave Slam Forces
- Barge Flexibility (Hog / Sag)
- Cargo Barge Strength Assessment
- Load path verification
DEFORMED PIPELINE
FATIGUE LIFE CASE
- Pipe Local Buckling event, while changing the Stinger radius
- Internal caliper Pig (ICP) showing Pipe ID deviation
- Modeling the deformed pipe using the ICP data in Inventor
- Modeling Elasto-Plastic X70 Stress-strain curve (Ramberg Osgood) in ANSYS
![](https://marin-tek.com/wp-content/uploads/2023/08/FATIGUE-LIFE-CASE-1.png)
![](https://marin-tek.com/wp-content/uploads/2023/08/SCF-CALCULATION-CASE-1.png)
SCF CALCULATION CASE
- Calculating the Axial SCF (177.5 bar) & Temperature range = -0.4C to 18.8C
- Calculate the Pipe Strain, using indenters recreating the feature
- Estimate the pipe fatigue life using weld SN curves
NAVAL ANALYSIS
Mooring Analysis(Side by Side DP Mode)
![](https://marin-tek.com/wp-content/uploads/2023/07/Mooring-Analysis-1.jpg)
Mooring Analysis(Pipelay in DP Assisted Mode)
![](https://marin-tek.com/wp-content/uploads/2023/07/Mooring-Analysis-2.jpg)
Mooring Analysis(Pipelay in Anchor Mode)
![](https://marin-tek.com/wp-content/uploads/2023/07/Mooring-Analysis-3.jpg)
Jacket Upending Analysis
![](https://marin-tek.com/wp-content/uploads/2023/07/Jacket-Upending-Analysis-1.jpg)
![](https://marin-tek.com/wp-content/uploads/2023/07/Jacket-Upending-Analysis-2.jpg)
MOORING SYSTEM DESIGN
![](https://marin-tek.com/wp-content/uploads/2023/07/MOORING-SYSTEM-DESIGN-3.jpg)
![](https://marin-tek.com/wp-content/uploads/2023/07/MOORING-SYSTEM-DESIGN-2.jpg)